S. Tobias and W. Fishwick, Theory of regenerative machine tool chatter, Engineer, vol.205, pp.199-203, 1958.

J. Tlusty, Dynamics of High-Speed Milling, Journal of Engineering for Industry, vol.108, issue.2, pp.59-67, 1986.
DOI : 10.1115/1.3187052

Y. Altintas and E. Budak, Analytical Prediction of Stability Lobes in Milling, CIRP Annals - Manufacturing Technology, vol.44, issue.1, pp.357-362, 1995.
DOI : 10.1016/S0007-8506(07)62342-7

S. Smith and J. Tlusty, Efficient Simulation Programs for Chatter in Milling, CIRP Annals - Manufacturing Technology, vol.42, issue.1, pp.463-466, 1993.
DOI : 10.1016/S0007-8506(07)62486-X

M. Davies, J. Pratt, B. Dutterer, and T. Burns, Stability Prediction for Low Radial Immersion Milling, Journal of Manufacturing Science and Engineering, vol.124, issue.2, pp.217-225, 2002.
DOI : 10.1115/1.1455030

T. Insperger, B. Mann, G. Stépán, and P. Bayly, Stability of up-milling and down-milling, part 1: alternative analytical methods, International Journal of Machine Tools and Manufacture, vol.43, issue.1, pp.25-34, 2003.
DOI : 10.1016/S0890-6955(02)00159-1

M. Campomanes and Y. Altintas, An Improved Time Domain Simulation for Dynamic Milling at Small Radial Immersions, Journal of Manufacturing Science and Engineering, vol.125, issue.3, pp.416-422, 2003.
DOI : 10.1115/1.1580852

P. Bayly, J. Halley, B. Mann, and M. Davies, Stability of Interrupted Cutting by Temporal Finite Element Analysis, Journal of Manufacturing Science and Engineering, vol.125, issue.2, pp.220-225, 2003.
DOI : 10.1115/1.1556860

S. Merdol and Y. Altintas, Multi Frequency Solution of Chatter Stability for Low Immersion Milling, Journal of Manufacturing Science and Engineering, vol.126, issue.3, pp.459-466, 2004.
DOI : 10.1115/1.1765139

H. Paris, G. Peigné, and R. Mayer, Surface shape prediction in high speed milling, International Journal of Machine Tools and Manufacture, vol.44, issue.15, pp.1567-1576, 2004.
DOI : 10.1016/j.ijmachtools.2004.06.005

E. Solis, C. Peres, J. Jiménez, J. Alique, and J. Monje, A new analytical???experimental method for the identification of stability lobes in high-speed milling, International Journal of Machine Tools and Manufacture, vol.44, issue.15, pp.1591-1597, 2004.
DOI : 10.1016/j.ijmachtools.2004.06.011

T. Surmann and D. Enk, Simulation of milling tool vibration trajectories along changing engagement conditions, International Journal of Machine Tools and Manufacture, vol.47, issue.9, pp.1442-1448, 2007.
DOI : 10.1016/j.ijmachtools.2006.09.030

S. Seguy, F. Campa, L. De-lacalle, L. Arnaud, L. Dessein et al., Toolpath dependent stability lobes for the milling of thin-walled parts, International Journal of Machining and Machinability of Materials, vol.4, issue.4, pp.377-392, 2008.
DOI : 10.1504/IJMMM.2008.023720
URL : https://hal.archives-ouvertes.fr/hal-00963033

S. Seguy, G. Dessein, and L. Arnaud, Surface roughness variation of thin wall milling, related to modal interactions, International Journal of Machine Tools and Manufacture, vol.48, issue.3-4, pp.261-274, 2008.
DOI : 10.1016/j.ijmachtools.2007.09.005
URL : https://hal.archives-ouvertes.fr/hal-00748570

J. Tlusty, S. Smith, and W. Winfough, Techniques for the Use of Long Slender End Mills in High-speed Milling, CIRP Annals - Manufacturing Technology, vol.45, issue.1, pp.393-396, 1996.
DOI : 10.1016/S0007-8506(07)63088-1

G. Duncan, M. Tummond, and T. Schmitz, An investigation of the dynamic absorber effect in high-speed machining, International Journal of Machine Tools and Manufacture, vol.45, issue.4-5, pp.497-507, 2005.
DOI : 10.1016/j.ijmachtools.2004.09.005

Y. Altintas, S. Engin, and E. Budak, Analytical Stability Prediction and Design of Variable Pitch Cutters, Journal of Manufacturing Science and Engineering, vol.121, issue.2, pp.173-178, 1999.
DOI : 10.1115/1.2831201

E. Budak, An Analytical Design Method for Milling Cutters With Nonconstant Pitch to Increase Stability, Part I: Theory, Journal of Manufacturing Science and Engineering, vol.125, issue.1, pp.29-34, 2003.
DOI : 10.1115/1.1536655

B. Stone, The effect on the chatter behaviour of machine tools of cutters with different helix angles on adjacent teeth, Proceedings of the 11th MTDR Conference, pp.169-180, 1970.

N. Sims, B. Mann, and S. Huyanan, Analytical prediction of chatter stability for variable pitch and variable helix milling tools, Journal of Sound and Vibration, vol.317, issue.3-5, pp.664-686, 2008.
DOI : 10.1016/j.jsv.2008.03.045

T. Takemura, T. Kitamura, T. Hoshi, and K. Okushima, Active suppression of chatter by programmed variation of spindle speed, Ann CIRP, vol.23, pp.121-122, 1974.

J. Sexton, R. Milne, and B. Stone, A stability analysis of single-point machining with varying spindle speed, Applied Mathematical Modelling, vol.1, issue.6, pp.310-318, 1977.
DOI : 10.1016/0307-904X(77)90062-2

J. Sexton and B. Stone, The stability of machining with continuously varying spindle speed, Ann CIRP, vol.27, pp.321-326, 1978.

J. Sexton and B. Stone, An investigation of the transient effects during variable speed cutting, ARCHIVE: Journal of Mechanical Engineering Science 1959-1982 (vols 1-23), vol.22, issue.3, pp.107-118, 1980.
DOI : 10.1243/JMES_JOUR_1980_022_024_02

T. Tsao, M. Mccarthy, and S. Kapoor, A new approach to stability analysis of variable speed machining systems, International Journal of Machine Tools and Manufacture, vol.33, issue.6, pp.791-808, 1993.
DOI : 10.1016/0890-6955(93)90038-V

S. Jayaram, S. Kapoor, and R. Devor, Analytical Stability Analysis of Variable Spindle Speed Machining, Journal of Manufacturing Science and Engineering, vol.122, issue.3, pp.391-397, 2000.
DOI : 10.1115/1.1285890

T. Insperger and G. Stépán, Stability Analysis of Turning With Periodic Spindle Speed Modulation Via Semidiscretization, Journal of Vibration and Control, vol.10, issue.12, pp.1835-1855, 2004.
DOI : 10.1177/1077546304044891

H. Zhang, M. Jackson, and J. Ni, Stability analysis on spindle speed variation method for machining chatter suppression, International Journal of Machining and Machinability of Materials, vol.5, issue.1, pp.107-128, 2009.
DOI : 10.1504/IJMMM.2009.023116

E. Al-regib, J. Ni, and S. Lee, Programming spindle speed variation for machine tool chatter suppression, International Journal of Machine Tools and Manufacture, vol.43, issue.12, pp.1229-1240, 2003.
DOI : 10.1016/S0890-6955(03)00126-3

F. Yang, B. Zhang, and Y. J. , Chatter suppression with multiple time-varying parameters in turning, Journal of Materials Processing Technology, vol.141, issue.3, pp.431-438, 2003.
DOI : 10.1016/S0924-0136(03)00427-8

S. Sastry, S. Kapoor, and R. Devor, Floquet Theory Based Approach for Stability Analysis of the Variable Speed Face-Milling Process, Journal of Manufacturing Science and Engineering, vol.124, issue.1, pp.10-17, 2002.
DOI : 10.1115/1.1418695

M. Zatarain, I. Bediaga, J. Muñoa, and R. Lizarralde, Stability of milling processes with continuous spindle speed variation: Analysis in the frequency and time domains, and experimental correlation, CIRP Annals - Manufacturing Technology, vol.57, issue.1, pp.379-384, 2008.
DOI : 10.1016/j.cirp.2008.03.067

Y. Altintas and P. Chan, In-process detection and suppression of chatter in milling, International Journal of Machine Tools and Manufacture, vol.32, issue.3, pp.329-347, 1992.
DOI : 10.1016/0890-6955(92)90006-3

I. Bediaga, I. Egaña, and J. Muñoa, Reducción de la inestabilidad en cortes interrumpidos en fresado a alta velocidad mediante variación de la velocidad del husillo, XVI Congreso de Máquinas-Herramienta y Tecnologías de Fabricación, 2006.

R. Radulescu, S. Kapoor, and R. Devor, An Investigation of Variable Spindle Speed Face Milling for Tool-Work Structures With Complex Dynamics, Part 2: Physical Explanation, Journal of Manufacturing Science and Engineering, vol.119, issue.3, pp.273-280, 1997.
DOI : 10.1115/1.2831104

T. Insperger and G. Stépán, Semi-discretization method for delayed systems, International Journal for Numerical Methods in Engineering, vol.33, issue.1, pp.503-518, 2002.
DOI : 10.1002/nme.505

S. Lin, R. Devor, and S. Kapoor, The Effects of Variable Speed Cutting on Vibration Control in Face Milling, Journal of Engineering for Industry, vol.112, issue.1, pp.1-11, 1990.
DOI : 10.1115/1.2899290

X. Long, B. Balachandran, and B. Mann, Dynamics of milling processes with variable time delays, Nonlinear Dynamics, vol.262, issue.1-3, pp.49-63, 2007.
DOI : 10.1007/s11071-006-9058-4

R. Faassen, N. Van-de-wouw, H. Nijmeijer, and J. Oosterling, An Improved Tool Path Model Including Periodic Delay for Chatter Prediction in Milling, Journal of Computational and Nonlinear Dynamics, vol.2, issue.2, pp.167-179, 2007.
DOI : 10.1115/1.2447465

T. Insperger, G. Stépán, and J. Turi, On the higher-order semi-discretizations for periodic delayed systems, Journal of Sound and Vibration, vol.313, issue.1-2, pp.334-341, 2008.
DOI : 10.1016/j.jsv.2007.11.040

B. Mann, T. Insperger, G. Stépán, and P. Bayly, Stability of up-milling and down-milling, part 2: experimental verification, International Journal of Machine Tools and Manufacture, vol.43, issue.1, pp.35-40, 2003.
DOI : 10.1016/S0890-6955(02)00160-8