B. Castanie, It was due to stress concentration that located at the periphery of the bolt or the drilled hole. For [2/4/4/10] and off-axis stackings, off-set failures were identified. These failures were not due to bearing stresses but to an edge delamination, followed by a local buckling. The results obtained in this study are the basis for developing more robust sizing methods for bolted joints based on physical understanding of failure mechanism and associated sensitivity parameters

J. M. Whitney and J. Nuismer, Stress criteria for laminated composites containing stress concentration, Journal of composite materials, issue.8, pp.254-264, 1974.

, Structural Element Characterization, vol.17

C. Hung and F. Chang, Strength Envelope of Bolted Composite Joints under Bypass Loads, vol.30, p.1402, 1996.

A. Valenza, V. Fiore, C. Borsellino, L. Calabrese, D. Bella et al., Failure Map of Composite Laminate Mechanical Joint, Journal of Composite Materials, p.951, 2007.

E. Persson, E. Madenci, and I. Eriksson, Delamination initiation of laminates with pin-loaded holes, Theoretical and Applied Fracture Mechanics, vol.30, pp.87-101, 1998.

T. Ireman, T. Ranvik, and I. Erikksson, On damage development in mechanically fastened composite laminates, Composite Structures, vol.49, 2000.

M. A. Mccarthy, V. P. Lawlor, W. F. Stanley-er, and C. T. Mccarthy, Bolt-hole clearance effects and strength criteria in single-bolt, single-lap, composite bolted joints, Composite Science and Technology, vol.62, pp.1415-1431, 2002.

R. A. Naik and J. H. Crews, Stress analysis method for clearance fit-bolt under bearings load, AIAA Journal, vol.24, pp.1348-1353, 1985.

L. Tong, Bearing failure of composite bolted joints with non-uniform bolt-to-washer clearance, Composites Part A: Applied science and manufacturing, vol.31, pp.609-615, 2000.

H. Park, Effects of stacking sequence and clamping force on the bearing strengths of mechanically fastened joints in composite laminates, Composite Structures, vol.53, pp.213-221, 2001.

H. Park, Bearing failure analysis of mechanically fastened joints in composite laminates, Composite Structures, vol.53, pp.199-211, 2001.

H. Wang and C. Hung, Bearing failure of bolted composite joints. Part I: Experimental characterization, Journal of composite materials, vol.30, issue.12, 1996.

C. Hung and F. Chang, Bearing failure of bolted composite joints. Part II: Model and verification, Journal of composite materials, vol.30, issue.12, pp.1359-1400, 1996.

G. Gohorianu, R. Piquet, F. Lachaud, and J. Barrau, Composite bolted joints behaviour: Effects of hole machining defects, Second international conference on Joining Plastics, 2006.

G. Gohorianu, Interaction between drilling defects and bearing behaviour of carbon/epoxy bolted joints, ISAE, 2008.

Y. Yan, W. Wen, F. Chang, and P. Shyprykevich, Experimental study on clamping effects on the tensile strength of composite plates with a bolt-filed hole, Composite Part A, Applied science and manufacturing, vol.30, pp.1215-1229, 1999.

A. J. Sawicki and P. J. Minguet, The influence of fastener clearance upon the failure of compression loadec composite bolted joints, ASTM STP 1383, pp.293-308

J. Wang and J. N. Dickson, Interlaminar Stresses in Symmetric Composite Laminates, Journal of Composite Materials, 1978.